{"title":"Audio-Technica","description":"","products":[{"product_id":"audio-technica-at-oc9-iii-microcoil-cartridge","title":"Audio-Technica AT-OC9XML Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT-OC9XML Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eThe AT-OC9XML Dual Moving Coil cartridge with Microlinear stylus is designed to provide outstanding channel separation. The Pure Copper by Ohno Continuous Casting (PCOCC) coils ensure pure audio transmission and are aligned in a reverse V-shaped formation to exert less pressure on the stylus, thereby minimizing distortion.\u003c\/p\u003e\n\u003cp\u003eAudio quality is further enhanced by a rigid aluminum body that reduces resonance, a neodymium magnet, and premium permendur yoke that increase the magnetic energy. The nude Microlinear stylus on a boron cantilever tracks the record groove with incredible accuracy, low distortion, and high transient response. The cartridge body has been pre-threaded, enabling it to be mounted to a headshell or integral tonearm with just two screws – no nuts required.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 x washers\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (5, 8, 10, 12 mm × 2 each)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eType:\u003c\/strong\u003e Dual moving coil\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBody:\u003c\/strong\u003e Aluminum\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e Microlinear, nude square shank\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Wire:\u003c\/strong\u003e PCOCC\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTerminal Pins:\u003c\/strong\u003e Brass\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus Curvature:\u003c\/strong\u003e 2.2 x 0.12 mil\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e 0.28 mm diameter nude boron\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e 20 x 10-6 cm\/dyne\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance:\u003c\/strong\u003e 16 x 10-6 cm\/dyne (100 Hz)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMount:\u003c\/strong\u003e Half-inch, threaded body\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e 20-47,000 Hz\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e 27 dB (1 kHz)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e 20°\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e 1.8-2.2 g (2.0 g standard)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e Min. 100 Ohm\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Impedance:\u003c\/strong\u003e 12 Ohm \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDC Resistance:\u003c\/strong\u003e 12 Ohm\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Inductance:\u003c\/strong\u003e 25 mH \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e 0.4 mV \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e 1.0 dB (1 kHz)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 × 16.8 × 25.7 mm\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 7.6 g (0.3 oz)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":28783098855484,"sku":"AT-OC9XML","price":649.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at_oc9xml_1_sq.jpg?v=1741631679"},{"product_id":"at-oc9xeb-dual-moving-coil-cartridge","title":"Audio-Technica AT-OC9XEB Dual Moving Coil Cartridge","description":"\u003ch1\u003e\u003c\/h1\u003e\n\u003ch1\u003eAudio-Technica AT-OC9XEB Dual Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eThe AT-OC9XEB Dual Moving Coil cartridge with bonded elliptical stylus is designed to provide outstanding channel separation. The Pure Copper by Ohno Continuous Casting (PCOCC) coils ensure pure audio transmission and are aligned in a reverse V-shaped formation to exert less pressure on the stylus, thereby minimizing distortion. Audio quality is further enhanced by a rigid aluminum body that reduces resonance, a neodymium magnet and pure iron yoke that increase the magnetic energy, and the bonded elliptical stylus on an aluminum cantilever that accurately tracks the record groove. The cartridge body has been pre-threaded, enabling it to be mounted to a headshell or integral tonearm with just two screws – no nuts required.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDual moving coil design, featuring independent coils for both left and right channels, provides outstanding channel separation\u003c\/li\u003e\n\u003cli\u003eThe coils are aligned in a reverse V-shaped formation, which exerts less pressure on the stylus, thereby minimizing distortion\u003c\/li\u003e\n\u003cli\u003eThe cartridge body is pre-threaded, enabling it to be mounted onto the headshell or integral tonearm with just two screws – no nuts required\u003c\/li\u003e\n\u003cli\u003eFeatures a bonded elliptical stylus and aluminum cantilever\u003c\/li\u003e\n\u003cli\u003eA neodymium magnet and pure iron yoke provide increased magnetic energy\u003c\/li\u003e\n\u003cli\u003eAluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction\u003c\/li\u003e\n\u003cli\u003ePure copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 x washers\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (5, 8, 10, 12 mm × 2 each)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e Specifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eType: \u003c\/strong\u003eDual moving coil, aluminum body\u003cstrong\u003e\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e\u003cspan\u003e Bonded round shank\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e\u003cspan\u003e Aluminum pipe\u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e 20 x 10-6 cm\/dyne\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance: \u003c\/strong\u003e9 x 10-6 cm\/dyne \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMount:\u003c\/strong\u003e\u003cspan\u003e Half-inch\u003cstrong\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e 20\u003cspan\u003e-30,000 Hz\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e\u003cspan\u003e 25 dB \u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e\u003cspan\u003e 20 degrees\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e\u003cspan\u003e 1.8-2.2 g (standard: 2 g)\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e\u003cspan\u003e Min. 100 Ohm\u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e\u003cspan\u003e 0.32 mV \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e\u003cspan\u003e 1.5 dB \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 x 16.8 x 25.7 mm \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 7.6 g\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":31804927737916,"sku":"AT-OC9XEB","price":279.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at_oc9xeb_1_sq.jpg?v=1741631453"},{"product_id":"at-oc9xen-dual-moving-coil-cartridge","title":"Audio-Technica AT-OC9XEN Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT-OC9XEN Dual Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eThe AT-OC9XEN Dual Moving Coil cartridge with nude elliptical stylus is designed to provide outstanding channel separation. The Pure Copper by Ohno Continuous Casting (PCOCC) coils ensure pure audio transmission and are aligned in a reverse V-shaped formation to exert less pressure on the stylus, thereby minimizing distortion.\u003c\/p\u003e\n\u003cp\u003eAudio quality is further enhanced by a rigid aluminum body that reduces resonance, a neodymium magnet and pure iron yoke that increase the magnetic energy, and the low-mass nude elliptical stylus on an aluminum cantilever that accurately tracks the record groove. The cartridge body has been pre-threaded, enabling it to be mounted to a headshell or integral tonearm with just two screws – no nuts required.\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDual moving coil design, featuring independent coils for both left and right channels, provides outstanding channel separation\u003c\/li\u003e\n\u003cli\u003eThe coils are aligned in a reverse V-shaped formation, which exerts less pressure on the stylus, thereby minimizing distortion\u003c\/li\u003e\n\u003cli\u003eThe cartridge body is pre-threaded, enabling it to be mounted onto the headshell or integral tonearm with just two screws – no nuts required\u003c\/li\u003e\n\u003cli\u003eFeatures low mass nude elliptical stylus and aluminum cantilever\u003c\/li\u003e\n\u003cli\u003eA neodymium magnet and pure iron yoke provide increased magnetic energy\u003c\/li\u003e\n\u003cli\u003eAluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction\u003c\/li\u003e\n\u003cli\u003ePure copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 x washers\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (5, 8, 10, 12 mm × 2 each)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eType:\u003cspan\u003e \u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003eDual moving coil, aluminum body\u003c\/span\u003e\u003cstrong\u003e\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e\u003cspan\u003e Elliptical nude\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e\u003cspan\u003e Aluminum pipe\u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e\u003cspan\u003e 20 x 10-6 cm\/dyne\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance: \u003c\/strong\u003e\u003cspan\u003e9 x 10-6 cm\/dyne\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMount:\u003c\/strong\u003e\u003cspan\u003e Half-inch\u003cstrong\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e\u003cspan\u003e 20\u003c\/span\u003e\u003cspan\u003e-30,000 Hz\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e\u003cspan\u003e 25 dB \u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e\u003cspan\u003e 20 degrees\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e\u003cspan\u003e 1.8-2.2 g (standard: 2 g)\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e\u003cspan\u003e Min. 100 Ohm\u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e\u003cspan\u003e 0.35 mV \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e\u003cspan\u003e 1.5 dB \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 x 16.8 x 25.7 mm\u003c\/span\u003e\u003cspan\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 7.6 g\u003c\/span\u003e\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":31804930031676,"sku":"AT-OC9XEN","price":399.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at_oc9xen_1_sq.jpg?v=1741631451"},{"product_id":"at-oc9xsh-dual-moving-coil-cartridge","title":"Audio-Technica AT-OC9XSH Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT-OC9XSH Dual Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eThe AT-OC9XSH Dual Moving Coil cartridge with Shibata stylus is designed to provide outstanding channel separation. The Pure Copper by Ohno Continuous Casting (PCOCC) coils ensure pure audio transmission and are aligned in a reverse V-shaped formation to exert less pressure on the stylus, thereby minimizing distortion.\u003c\/p\u003e\n\u003cp\u003eAudio quality is further enhanced by a rigid aluminum body that reduces resonance, a neodymium magnet and premium permendur yoke that increase the magnetic energy, and the nude Shibata stylus on a boron cantilever that tracks the record groove with incredible accuracy, delivering rich, full-range audio and high transient response. The cartridge body has been pre-threaded, enabling it to be mounted to a headshell or integral tonearm with just two screws – no nuts required.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDual moving coil design, featuring independent coils for both left and right channels, provides outstanding channel separation\u003c\/li\u003e\n\u003cli\u003eThe coils are aligned in a reverse V-shaped formation, which exerts less pressure on the stylus, thereby minimizing distortion\u003c\/li\u003e\n\u003cli\u003eThe cartridge body is pre-threaded, enabling it to be mounted onto the headshell or integral tonearm with just two screws – no nuts required\u003c\/li\u003e\n\u003cli\u003eFeatures nude Shibata stylus and boron cantilever for rich full-range audio reproduction and high transient response\u003c\/li\u003e\n\u003cli\u003eA neodymium magnet and permendur yoke provide dramatically increased magnetic energy\u003c\/li\u003e\n\u003cli\u003eAluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction\u003c\/li\u003e\n\u003cli\u003ePure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 x washers\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (5, 8, 10, 12 mm × 2 each)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eType:\u003cspan\u003e \u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003eDual moving coil, aluminum body\u003c\/span\u003e\u003cstrong\u003e\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e\u003cspan\u003e Shibata\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e\u003cspan\u003e Aluminum pipe\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e\u003cspan\u003e 20\u003c\/span\u003e\u003cspan\u003e-47,000 Hz\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e\u003cspan\u003e 27 dB \u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e\u003cspan\u003e 20 degrees\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e\u003cspan\u003e 1.8-2.2 g (standard: 2 g)\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e\u003cspan\u003e Min. 100 Ohm \u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e\u003cspan\u003e 0.4 mV \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e\u003cspan\u003e 1 dB \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e\u003cspan\u003e 20 x 10-6 cm\/dyne\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance: \u003c\/strong\u003e\u003cspan\u003e9 x 10-6 cm\/dyne (100 Hz)\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMount:\u003c\/strong\u003e\u003cspan\u003e Half-inch\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 x 16.8 x 25.7 mm \u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 7.6 g\u003c\/span\u003e\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":31804931080252,"sku":"AT-OC9XSH","price":759.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at_oc9xsh_1_sq.jpg?v=1741631449"},{"product_id":"audio-technica-at-oc9xsl-dual-moving-coil-cartridge","title":"Audio-Technica AT-OC9XSL Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT-OC9XSL Dual Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eThe AT-OC9XSL Dual Moving Coil cartridge with special line contact stylus is designed to provide outstanding channel separation. The Pure Copper by Ohno Continuous Casting (PCOCC) coils ensure pure audio transmission and are aligned in a reverse V-shaped formation to exert less pressure on the stylus, thereby minimizing distortion.\u003c\/p\u003e\n\u003cp\u003eAudio quality is further enhanced by a rigid aluminum body that reduces resonance, a neodymium magnet and premium permendur yoke that dramatically increase the magnetic energy, and the nude special line contact stylus on a boron cantilever that tracks the record groove with ultimate accuracy, delivering rich, full-range audio and high transient response. The cartridge body has been pre-threaded, enabling it to be mounted to a headshell or integral tonearm with just two screws – no nuts required.\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDual moving coil design, featuring independent coils for both left and right channels, provides outstanding channel separation\u003c\/li\u003e\n\u003cli\u003eThe coils are aligned in a reverse V-shaped formation, which exerts less pressure on the stylus, thereby minimizing distortion\u003c\/li\u003e\n\u003cli\u003eThe cartridge body is pre-threaded, enabling it to be mounted onto the headshell or integral tonearm with just two screws – no nuts required\u003c\/li\u003e\n\u003cli\u003eFeatures nude Special Line Contact stylus and boron cantilever with accurate tracking ability and high transient response\u003c\/li\u003e\n\u003cli\u003eA neodymium magnet and permendur yoke provide dramatically increased magnetic energy\u003c\/li\u003e\n\u003cli\u003eAluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction\u003c\/li\u003e\n\u003cli\u003ePure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve pure signal transfer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 x washers\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (5, 8, 10, 12 mm × 2 each)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e\u003cspan\u003e Special line contact\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e\u003cspan\u003e 0.28 mm nude boron\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eType:\u003cspan\u003e \u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003eDual moving coil, aluminum body\u003c\/span\u003e\u003cstrong\u003e\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e\u003cspan\u003e 20\u003c\/span\u003e\u003cspan\u003e-50,000 Hz\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e\u003cspan\u003e 28 dB \u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e\u003cspan\u003e 20 degrees\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e\u003cspan\u003e 1.8-2.2 g (standard: 2 g)\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e\u003cspan\u003e Min. 100 Ohm \u003cbr\u003e\u003c\/span\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e\u003cspan\u003e 0.4 mV \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e\u003cspan\u003e 0.5 dB \u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e\u003cspan\u003e 22 x 10-6 cm\/dyne\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance:\u003c\/strong\u003e 18\u003cspan\u003e x 10-6 cm\/dyne (100 Hz)\u003c\/span\u003e\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMount:\u003c\/strong\u003e\u003cspan\u003e Half-inch\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 x 16.8 x 25.7 mm \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 7.6 g\u003c\/span\u003e\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":31804931637308,"sku":"AT-OC9XSL","price":819.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at_oc9xsl_1_sq.jpg?v=1741631448"},{"product_id":"audio-technica-at33ev-dual-moving-coil-cartridge","title":"Audio-Technica AT33EV Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT33EV Dual Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eThe new half-inch standard mount 0.3 x 0.7 mil elliptical AT33EV cartridge features a tapered duralumin cantilever. The dual moving coil cartridge design increases channel separation and extends the frequency response range delivering extraordinary audio quality. Internally constructed with neodymium magnet for enhanced magnetic energy and PCOCC wire for pure audio transmission.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e 0.3 x 0.7 mil nude elliptical\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e Duralumin tapered pipe\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMount:\u003c\/strong\u003e Half-inch\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e 15-50,000 Hz\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e 30 dB (1 kHz)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e 1.8-2.2 g (2 g standard)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e 100 Ohm\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e 0.3 mV \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e 0.5 dB \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":31804952313916,"sku":"AT33EV","price":499.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at33ev_1_sq.jpg?v=1741631446"},{"product_id":"audio-technica-at-sut1000-moving-coil-step-up-transformer","title":"Audio-Technica AT-SUT1000 Moving Coil Step-Up Transformer","description":"\u003ch1\u003eAudio-Technica AT-SUT1000 Moving Coil Step-Up Transformer\u003c\/h1\u003e\n\u003cp\u003eEmploying the finest materials and production methods, the AT-SUT1000 MC step-up transformer is built to deliver unaltered sound from a moving coil phono cartridge for the best analog listening experience possible. It features a special hand-wound, large-core transformer that is capable of a wide range of voltages, making it ideal for stepping up low-impedance moving coil cartridges.\u003c\/p\u003e\n\u003cp\u003eThe transformer maintains a balanced signal from the moving-coil cartridge through to the phono preamp. Or users can opt for an unbalanced connection, if desired. The AT-SUT1000 utilizes HANENITE® rubber mounting to suppress vibrations and permalloy magnetic shielding to block external noise.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eA high-quality MC step-up transformer, compatible with balanced and unbalanced connections\u003c\/li\u003e\n\u003cli\u003eSpecial hand-wound, large-core transformer is capable of a wide range of voltages, making it ideal for stepping up low-impedance moving coil cartridges\u003c\/li\u003e\n\u003cli\u003eTransformer maintains balanced signal from the cartridge through to the phono preamp (RCA input and output are also available)\u003c\/li\u003e\n\u003cli\u003eUtilizes HANENITE® rubber mounting to suppress vibrations and permalloy magnetic shielding to block external noise\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response (-3 dB to 1 dB at 3, 10, 17 Ohm): \u003c\/strong\u003e 10 - 200 kHz, 10 - 60 kHz, 10 to 40 kHz \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e Stereo RCA or XLR\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eGain:\u003c\/strong\u003e 22 dB\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCartridge Impedance Range:\u003c\/strong\u003e 2-17 Ohm\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load:\u003c\/strong\u003e 47,000 Ohm\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Balance:\u003c\/strong\u003e \u0026lt;0.5 dB \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e \u0026gt;100 dB \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 3.6\" x 7.7\" x 5.9\" (92 × 196 × 150 mm)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 11 lb. (5 kg)\u003cbr\u003e\u003cstrong\u003eSupplied accessories:\u003c\/strong\u003e 1 m (3.3') ground wire\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":31804952870972,"sku":"AT-SUT1000","price":4999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at_sut1000_1_sq.jpg?v=1741631445"},{"product_id":"audio-technica-art-9xi-moving-coil-cartridge","title":"Audio-Technica ART-9xi Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica ART-9xi Moving Coil Cartridge\u003c\/h1\u003e\n\u003ch2\u003eFeaturing a special line contact stylus on a 0.28 mm diameter solid boron cantilever, the AT-ART9XI replaces the AT-ART9 as Audio-Technica’s flagship magnetic core MC cartridge\u003c\/h2\u003e\n\u003cp\u003eThis Audio-Technica Reference Transducer, uses a specially designed magnetic circuit that boasts an output voltage of 0.5 mV (1 kHz, 5 cm\/sec), making the cartridge capable of reproducing even the most delicate signals and nuance, while also ensuring dynamic playback. The dual moving coils (fashioned from high-performance PCOCC wire) are aligned in an inverted V shape to provide high separation and wide response for clear sound localization and minimal distortion. Threaded cartridge mounting holes make installation to a headshell or integrated tonearm incredibly easy.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAudio-Technica’s flagship magnetic core moving coil cartridge\u003c\/li\u003e\n\u003cli\u003eDual moving coils are aligned in an inverted V shape, providing high separation and wide response for clear sound localization and minimal distortion\u003c\/li\u003e\n\u003cli\u003eSpecial line contact stylus ensures faithful reproduction of the music signal, and the 0.28 mm diameter solid boron cantilever provides excellent response characteristics\u003c\/li\u003e\n\u003cli\u003eNeodymium magnet and permendur yoke significantly increase magnetic energy\u003c\/li\u003e\n\u003cli\u003eSpecially designed magnetic circuit provides an output voltage of 0.5 mV (1 kHz, 5 cm\/sec)\u003c\/li\u003e\n\u003cli\u003ePCOCC coils ensure high-fidelity transmission\u003c\/li\u003e\n\u003cli\u003eMachined aluminum base supports both the magnetic circuit and the vibration system, ensuring excellent playback stability\u003c\/li\u003e\n\u003cli\u003eHybrid body of machined aluminum and high-rigidity plastic reduces undesirable parasitic resonance\u003c\/li\u003e\n\u003cli\u003eThreaded cartridge mounting holes allow easy installation to a headshell or integrated tonearm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 x washers\u003c\/li\u003e\n\u003cli\u003eM2.6 cartridge installation screws (2 x 5 mm, 2 x 8 mm, 2 x 10 mm, 2 x 12 mm),\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003cli\u003eBrush\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStylus shape:\u003c\/strong\u003e Special line contact\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e 0.28 mm diameter solid boron\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMounting:\u003c\/strong\u003e Half-inch\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency response:\u003c\/strong\u003e 20-50,000 Hz\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical tracking angle:\u003c\/strong\u003e 20°\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical tracking force:\u003c\/strong\u003e 1.6-2.0 g (1.8 g standard)\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus construction:\u003c\/strong\u003e Nude\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended load impedance:\u003c\/strong\u003e Min. 100 Ohm (when head amplifier connected)\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil impedance \u003cmeta content=\"text\/html; charset=utf-8\" http-equiv=\"content-type\"\u003e(1 kHz):\u003c\/strong\u003e 12 Ohm \u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDC resistance:\u003c\/strong\u003e 12 Ohm\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil inductance \u003cmeta content=\"text\/html; charset=utf-8\" http-equiv=\"content-type\"\u003e(1 kHz):\u003c\/strong\u003e 25 µH \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput voltage \u003cmeta content=\"text\/html; charset=utf-8\" http-equiv=\"content-type\"\u003e(1 kHz, 5 cm\/sec):\u003c\/strong\u003e 0.5 mV \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003cstrong\u003eCartridge weight:\u003c\/strong\u003e 8.5 g (0.30 oz)\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (WHD):\u003c\/strong\u003e 0.66\" x 0.68\" x 0.98\" (\u003cmeta content=\"text\/html; charset=utf-8\" http-equiv=\"content-type\"\u003e16.8 x 17.3 × 25 mm) \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":37563340193976,"sku":"AT-ART9xi","price":1699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at-art9xi_04.jpg?v=1741631136"},{"product_id":"audio-technica-at-lp7-turntable-with-built-in-phono","title":"Audio-Technica AT-LP7 Turntable with built-in Phono","description":"\u003ch1\u003eAudio-Technica AT-LP7 Turntable with built-in Phono\u003c\/h1\u003e\n\u003ch2\u003eA fully manual, belt-drive turntable built around the VM cartridge line\u003c\/h2\u003e\n\u003cp\u003eThe AT-LP7 comes with a VM520EB Dual Moving Magnet Cartridge with a 10 g AT-HS10 headshell and 0.3 x 0.7 mil elliptical bonded stylus. That stylus can be replaced with any of the other six styli available in the VM line, allowing for easy stylus upgrades without buying a whole new cartridge.\u003cbr\u003e\u003cbr\u003eThe headshell attaches to a J-shaped tone arm that takes its inspiration from the classic A-T models of the 1960s and ’70s. The tonearm features a metallic gimbal suspension system and precision bearings to mitigate tracking errors, and includes an adjustable counterweight and anti-skate control. The height of the tonearm can be adjusted from 0 mm to 6 mm to accommodate a wide variety of cartridges.\u003cbr\u003e\u003cbr\u003eThe turntable chassis is constructed of 40 mm-thick MDF (medium density fiberboard), an excellent anti-vibration damping material that limits low-frequency acoustical feedback. The anti-resonance platter is made of 20 mm-thick polyoxymethylene and is driven by a sensor-monitored motor that ensures a continuously accurate platter rotation speed of 33-1\/3 or 45 RPM. The AT-LP7 also includes a built-in switchable phono\/line preamp for connection to components with or without a dedicated phono input, and a selector switch to designate operation with a moving magnet or moving coil cartridge.\u003cbr\u003e\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFully manual, belt-drive operation with two speeds: 33-1\/3 and 45 RPM\u003c\/li\u003e\n\u003cli\u003eMotor features a speed-sensor system to maintain accurate platter rotation speed\u003c\/li\u003e\n\u003cli\u003eVM520EB Dual Moving Magnet Cartridge provides outstanding channel separation and extended frequency response, and allows for easy replacement with any VM stylus\u003c\/li\u003e\n\u003cli\u003eJ-shaped tonearm features a metallic gimbal suspension system and precision bearings for excellent tracking\u003c\/li\u003e\n\u003cli\u003eBuilt-in switchable phono pre-amplifier with selectable modes for moving magnet or moving coil cartridges\u003c\/li\u003e\n\u003cli\u003e20 mm-thick, anti-resonance, polyoxymethylene platter\u003c\/li\u003e\n\u003cli\u003e40 mm-thick MDF (medium density fiberboard) chassis\u003c\/li\u003e\n\u003cli\u003eLightweight AT-HS10 headshell\u003c\/li\u003e\n\u003cli\u003eIncludes dual RCA (male) to dual RCA (male) stereo cable, 45 RPM adapter, and dust cover \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eType:\u003c\/strong\u003e Fully manual, belt drive\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpeeds:\u003c\/strong\u003e 33-1\/3, 45 RPM\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput level (\u003cmeta http-equiv=\"content-type\" content=\"text\/html; charset=utf-8\"\u003enominal at 1 kHz, 5 cm\/sec)\u003c\/strong\u003e\u003cbr\u003e\u003cmeta http-equiv=\"content-type\" content=\"text\/html; charset=utf-8\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong\u003ePre-amp (Phono):\u003c\/strong\u003e 4.5 mV \u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cstrong\u003ePre-amp (Line MM):\u003c\/strong\u003e 280 mV \u003c\/span\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePhono gain (MM, MC):\u003c\/strong\u003e 36 dB, 56 dB \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTonearm\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eType:\u003c\/strong\u003e Static balanced J-shaped tonearm\u003cbr data-mce-fragment=\"1\"\u003e\u003cstrong\u003eEffective length:\u003c\/strong\u003e 247 mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cstrong\u003eOverhang:\u003c\/strong\u003e 17 mm\u003cbr data-mce-fragment=\"1\"\u003e\u003cstrong\u003eMaximum tracking error angle:\u003c\/strong\u003e Less than 2.5°\u003cbr data-mce-fragment=\"1\"\u003e\u003cstrong\u003eStylus pressure adjustment range:\u003c\/strong\u003e 0 to 2.5 g\u003cbr data-mce-fragment=\"1\"\u003e\u003cstrong\u003eApplicable cartridge weight range (including headshell):\u003c\/strong\u003e 15 to 20 g\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (WDH):\u003c\/strong\u003e 17.72\" x 13.86\" x 6.18\" \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 18.3 lb\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":37563356971192,"sku":"AT-LP7","price":999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at-lp7_01.png?v=1741631134"},{"product_id":"audio-technica-at-dac100-digital-to-analog-converter","title":"Audio-Technica AT-DAC100 Digital to Analog Converter","description":"\u003ch1\u003eAudio-Technica AT-DAC100 Digital to Analog Converter\u003c\/h1\u003e\n\u003ch3\u003e\u003cspan\u003eA PCM 768-32, DSD 22.4 DAC matched especially to vacuum tube preamps.\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003eThis compact desktop DAC, which can be placed both horizontally and vertically, uses the AKM AK4452VN DAC chip offers a high signal-to-noise ratio and low distortion. Also, the AT-DAC100 is tuned for tueb preamps by suppressing high-frequency noise output, notably some switching and filters, making the unit ideally suited to the AT-BHA100 balanced headphone amplifier. \u003c\/p\u003e\n\u003cp\u003eThe low pass filter uses the audio-grade LME49860 operational amplifier from Texas Instruments for low distortion and superior attack performance. Once paired with the AT-BHA100 headphone amplifier, some great Audio Technica headphone pairings are the ATH-ADX5000, ATH-MSR7b, and the ATH-AW Series.\u003c\/p\u003e\n\u003cp\u003eThis versatile DAC has USB-C, USB-B, optical, and coaxial inputs, with sampling rates going up to 768 kHz, 32-bit for PCM, and 22.4 MHz for DSD. The coax and optical inputs are limited to 195 kHz, 24 bit.\u003c\/p\u003e\n\u003cp\u003eThe DAC ships with a high-quality external Analog Devices power supply. Key components include audio-grade Nichicon chemical capacitors, and WIMA film capacitors. \u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eInputs: \u003c\/strong\u003eUSB-B, USB-C, coax, optical\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput:\u003c\/strong\u003e Stereo RCA\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 1.73\" x 8.27\" x 5.31\" (44 x 210 × 135 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 35.3 oz (1 kg)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":40654295695544,"sku":"AT-DAC100","price":599.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at-dac100_01.jpg?v=1741630752"},{"product_id":"audio-technica-adx-5000-open-back-headphones","title":"Audio-Technica ADX-5000 Open Back Headphones","description":"\u003ch1\u003e\n\u003cmeta charset=\"utf-8\"\u003e \u003cspan\u003eAudio Technica ADX-5000 Open Back Headphones\u003c\/span\u003e\n\u003c\/h1\u003e\n\u003cdiv class=\"colOptions font-11 m-grey\"\u003eThe result of Japanese craftsmanship and expert engineering, the ATH-ADX5000 Hi-Res Audio headphones set a new standard in open-back headphone performance.\u003c\/div\u003e\n\u003cdiv class=\"colOptions font-11 m-grey\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"colOptions font-11 m-grey\"\u003eThe headphones use newly developed Core Mount Technology that optimally positions the driver unit within the housing to improve airflow efficiency. The efficient airflow helps the headphones reproduce highly transparent mid and high frequencies and rich, precise bass sound. The 58 mm integrated driver units combine a tungsten-coated diaphragm, baffle and Permendur magnetic circuit in a single unit to reduce unwanted vibration and, since no screw clamps are required, decrease the weight. The baffle is made of a highly-rigid polyphenylene sulfide (PPS)\/glass fiber composite to provide stable diaphragm movement.\u003c\/div\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":41894257426616,"sku":"ATH-ADX5000","price":2199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/ath-adx5000_01.jpg?v=1741630562"},{"product_id":"audio-technica-art-20-dual-moving-coil-cartridge","title":"Audio-Technica ART-20 Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio Technica ART-20 Dual Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eAudio-Technica is pleased to introduce the AT-ART20, the latest cartridge in the ART Series. The two main goals in developing the AT-ART20 were to provide superlative analog sound reproduction and optimize the performance and benefits of a magnetic core cartridge.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003cli\u003eWasher × 2\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws: 2 x M2.6, 2 x 8 mm, 2 x 10 mm, 2 x 12 mm\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e Special line contact\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus Curvature Radius:\u003c\/strong\u003e 1.5 × 0.28 mil\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e 0.28 mm (0.011”) diameter solid boron\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThreaded Hole:\u003c\/strong\u003e 2 x M2.6\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e20 to 50,000 Hz\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation (1 kHz):\u003c\/strong\u003e 30 dB \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e 20°\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Force:\u003c\/strong\u003e 1.6 to 2.0 g (1.8 g standard)\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus Construction:\u003c\/strong\u003e Nude\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load Impedance (When head amplifier connected):\u003c\/strong\u003e ≥ 100 Ohm \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Impedance (1 kHz):\u003c\/strong\u003e 12 Ohm\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDC Resistance:\u003c\/strong\u003e 12 Ohm\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Inductance (1 kHz):\u003c\/strong\u003e 25 μH\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput Voltage (1 kHz, 5 cm\/sec.):\u003c\/strong\u003e 0.55 mV \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e 23 × 10-6 cm\/dyne\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance:\u003c\/strong\u003e 13 × 10-6 cm\/dyne (100 Hz)\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 ×16.8 ×26.6 mm  \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCartridge Weight:\u003c\/strong\u003e 9 g \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":41944621514936,"sku":"AT-ART20","price":3199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/products\/at-art20_05.jpg?v=1741630556"},{"product_id":"audio-technica-at-art1000x-direct-power-moving-coil-cartridge","title":"Audio-Technica AT-ART1000X Direct Power Moving Coil Cartridge","description":"\u003cp\u003e\u003c!----\u003e\u003c\/p\u003e\n\u003ch1\u003eAudio-Technica AT-ART1000X Direct Power Moving Coil Cartridge\u003c\/h1\u003e\n\u003cp\u003eAudio-Technica’s transducer and cartridge technologies are acclaimed both in Japan and worldwide not only for their engineering precision and audio quality but also for their ability to provide a heightened listening experience.\u003c\/p\u003e\n\u003cp\u003eThe AT-ART1000 direct power stereo MC cartridge used a novel structure with the generator coils placed just above the stylus tip. This follow-up model, the AT-ART1000X, takes this philosophy and design to another level. A more refined direct power system enables three-dimensional spatial expression.\u003c\/p\u003e\n\u003cp\u003eThe AT-ART1000X has been developed, and manufactured in Japan, utilizing cutting-edge materials and design elements.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWooden case (Wooden box)\u003c\/li\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003eWasher x 2\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003cli\u003eM2.6 cartridge screws (2 x 5 mm, 2 x 8 mm, 2 x 10 mm, 2 x 12 mm)\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eType:\u003c\/strong\u003e Direct power system, non-magnetic core coil (MC) type\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStylus:\u003c\/strong\u003e Special line contact \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCurvature Radius:\u003c\/strong\u003e 1.5 x 0.28 mil\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCantilever:\u003c\/strong\u003e 0.26 mm boron\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFrequency Response:\u003c\/strong\u003e 15 to 30,000 Hz\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput Voltage:\u003c\/strong\u003e 0.22 mV\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChannel Separation:\u003c\/strong\u003e 30 dB\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput Balance:\u003c\/strong\u003e 0.5 dB\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTracking Force:\u003c\/strong\u003e (Refer to “Tracking force information” included in the box)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Impedance:\u003c\/strong\u003e 3.5 Ohm\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDC Resistance:\u003c\/strong\u003e 3.5 Ohm\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecommended Load Impedance:\u003c\/strong\u003e ≥ 30 Ohm\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoil Inductance:\u003c\/strong\u003e ≤ 1 μH \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStatic Compliance:\u003c\/strong\u003e 20 x 10-6 cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDynamic Compliance:\u003c\/strong\u003e 9 x 10-6 cm\/dyne \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Tracking Angle:\u003c\/strong\u003e 19°\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (HWD):\u003c\/strong\u003e 17.3 x 17 x 25.5 mm\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBolt Thread:\u003c\/strong\u003e 2 x M2.6 \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 11 g \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":48328563818680,"sku":"AT-ART1000X","price":5999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at-art1000x_05_png.webp?v=1741629815"},{"product_id":"audio-technica-at-lp8x-semi-automatic-direct-drive-turntable","title":"Audio-Technica AT-LP8X Semi-Automatic Direct-Drive Turntable","description":"\u003ch1\u003eAudio-Technica AT-LP8X Semi-Automatic Direct-Drive Turntable\u003cstrong\u003e\u003c\/strong\u003e\n\u003c\/h1\u003e\n\u003cp\u003eAudio-Technica's semi-automatic AT-LP8X features a newly designed tonearm lift that automatically raises the tonearm at the end of a record side and stops the motor.\u003c\/p\u003e\n\u003cp\u003eThe turntable’s J-shaped aluminum tonearm, inspired by classic A-T models of the 1960s and ’70s, comes equipped with a newly designed AT-LT10 headshell and AT-VM95E BK (black) cartridge with 0.3 x 0.7 mil elliptical stylus, providing excellent channel separation and low distortion for outstanding tonal quality. For easy customization, the stylus can be replaced or interchanged with any of the five additional styli in the VM95 line, and the tonearm’s VTA (vertical tracking angle) adjustment and sub-counterweight enable the use of a broad range of other cartridges.\u003c\/p\u003e\n\u003cp\u003eThe AT-LP8X plays 33-1\/3, 45, and 78 RPM records. Its 25 mm rubber-damped, anti-resonance, die-cast aluminum platter comes with a 2.5 mm rubber mat and is driven by a sensor-monitored motor that ensures a continuously accurate platter rotation speed. The motor and its efficient internal switching power supply are housed within a box plinth constructed of 16 mm MDF (medium-density fiberboard) and equipped with height-adjustable feet for excellent protection against unwanted noise and vibration.\u003c\/p\u003e\n\u003cp\u003eThe turntable comes with a detachable RCA output cable (dual RCA male to dual RCA male with ground), 45 RPM adapter, and removable hinged dust cover.  \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSemi-automatic direct-drive turntable with three speeds: 33-1\/3, 45, 78 RPM\u003c\/li\u003e\n\u003cli\u003eMotor features a speed-sensor system to maintain accurate platter rotation speed\u003c\/li\u003e\n\u003cli\u003eNewly designed low-torque, direct-drive DC servo motor improves wow and flutter performance\u003c\/li\u003e\n\u003cli\u003e25 mm rubber-damped, anti-resonance, die-cast aluminum platter with 2.5 mm rubber mat\u003c\/li\u003e\n\u003cli\u003eJ-shaped tonearm with adjustable VTA (vertical tracking angle)\u003c\/li\u003e\n\u003cli\u003eNewly designed tonearm lift automatically raises the tonearm at the end of a record side and stops the motor\u003c\/li\u003e\n\u003cli\u003eAT-VM95E BK (black) cartridge (0.3 x 0.7 mil elliptical stylus) is compatible with any VM95 Series replacement stylus, offering a wide choice of options for every budget and application\u003c\/li\u003e\n\u003cli\u003eNewly designed lightweight AT-LT10 headshell\u003c\/li\u003e\n\u003cli\u003eIncluded sub-counterweight provides an expanded cartridge\/headshell weight range of 14.0 g – 23.5 g\u003c\/li\u003e\n\u003cli\u003eNewly designed internal switching power supply, optimized for audio performance\u003c\/li\u003e\n\u003cli\u003eMDF (medium-density fiberboard) cabinet construction\u003c\/li\u003e\n\u003cli\u003ePhono-level output provides pure, direct transmission of the cartridge’s signal\u003c\/li\u003e\n\u003cli\u003eIncludes detachable RCA output cable (dual RCA male to dual RCA male with ground), 45 RPM adapter, and removable hinged dust cover\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDust cover\u003c\/li\u003e\n\u003cli\u003eRubber mat\u003c\/li\u003e\n\u003cli\u003eCounterweight and sub-counterweight\u003c\/li\u003e\n\u003cli\u003eHeadshell (AT-LT10) with VM stereo cartridge (AT-VM95E BK)\u003c\/li\u003e\n\u003cli\u003e45 RPM adapter\u003c\/li\u003e\n\u003cli\u003eRCA audio cable (1 m)\u003c\/li\u003e\n\u003cli\u003ePower cable (1.8 m)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMotor:\u003c\/strong\u003e DC servo\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDrive Method:\u003c\/strong\u003e Direct drive\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpeeds:\u003c\/strong\u003e 33-1\/3 RPM, 45 RPM, 78 RPM\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTurntable Platter:\u003c\/strong\u003e Die-cast aluminum, rubber damper\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWow and Flutter:\u003c\/strong\u003e \u0026lt;0.1%\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSignal-to-Noise Ratio:\u003c\/strong\u003e \u0026gt;60 dB\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutput Level:\u003c\/strong\u003e 4 mV\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePower Consumption:\u003c\/strong\u003e 8 W\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (WDH):\u003c\/strong\u003e 18\" x 14\" x 6.3\" (450 × 352 × 161 mm) \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 23 lb. (10.4 kg)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":50733025132728,"sku":"AT-LP8X","price":1299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at-lp8x_01copy.jpg?v=1741629516"},{"product_id":"audio-technica-at-lpa2-turntable","title":"Audio Technica AT-LPA2 Turntable","description":"\u003ch1\u003eAudio Technica AT-LPA2 Turntable\u003c\/h1\u003e\n\u003ch3\u003eA belt-drive with MC cartridge and separate power supply and control unit\u003c\/h3\u003e\n\u003cp\u003eThe AT-LPA2 is made from transparent acrylic, and is a fully manual belt-drive turntable that combines contemporary aesthetics with analog expertise, while remaining incredibly easy to set up and use.\u003c\/p\u003e\n\u003cp\u003eIt has been designed to minimize resonance, which can cause noise and distortion in the signal chain, while maximizing detailed audio reproduction of your vinyl records with crystal-clear accuracy. Not only is the acrylic stunning, it is also an ideal material for turntable construction, greatly reducing reverberations that might otherwise affect sound clarity.\u003c\/p\u003e\n\u003cp\u003eThe AT-LPA2 features a high-density, 30 mm transparent acrylic chassis and 20 mm platter to provide exceptional stability and vibration damping for pure, uncolored sound. Exclusively designed heavy-duty, height-adjustable feet isolate the turntable from vibration. The mass of the acrylic platter also allows it to spin at a consistent speed. Additionally, an optical sensor, positioned under the spindle, monitors platter rotation to maintain an accurate speed of 33-1\/3 or 45 RPM.\u003c\/p\u003e\n\u003cp\u003eTo further reduce unwanted noise, the controls and power supply are in a separate unit – a feature typically found only on more expensive turntables – thereby isolating the turntable’s sensitive audio components from electrical interference associated with powering and operating the turntable’s motor. This isolation ensures the quietest performance possible, so you hear only the music from your records, not electrical noise.\u003c\/p\u003e\n\u003cp\u003eThe AT-LPA2 comes with a pre-mounted AT-OC9XEN moving coil cartridge, which features a nude elliptical stylus (0.3 x 0.7 mil) and high-purity PCOCC coils. The AT-OC9XEN cartridge is designed to capture every nuance of your records with stunning clarity, while providing outstanding channel separation. The lower mass of the moving coil structure (compared to moving magnet cartridges) allows the stylus to react more quickly to changes in the record groove, resulting in more detailed audio reproduction.\u003c\/p\u003e\n\u003cp\u003eThe cartridge comes mounted to an exclusive machined-aluminum headshell with azimuth adjustment, that attaches to the straight, carbon-fiber tonearm. Engineered specifically for this turntable, the new 8.8-inch tonearm also offers VTA adjustment. The lightweight, anti-resonant tonearm tracks smoothly and precisely, utilizing a highly accurate, finely adjustable string-type anti-skate mechanism to counteract any inward pull and maintain proper channel balance. In addition, the tonearm includes two counterweight options (110 g and 130 g) to allow you to use a wide variety of other cartridges, should you so choose.\u003c\/p\u003e\n\u003cp\u003eWith its clean, modern look, advanced components, precision engineering, and ease of setup, the AT-LPA2 is your entry into the world of pure analog audio.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDust cover\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eCounterweights, light and heavy\u003c\/li\u003e\n\u003cli\u003eAnti-skate main and auxiliary weight \u003c\/li\u003e\n\u003cli\u003eHeadshell with MC stereo cartridge (AT-OC9XEN)\u003c\/li\u003e\n\u003cli\u003e45 RPM adapter\u003c\/li\u003e\n\u003cli\u003eRCA audio cable (1 m)\u003c\/li\u003e\n\u003cli\u003eControl cable (1 m)\u003c\/li\u003e\n\u003cli\u003eGround cable (1 m)\u003c\/li\u003e\n\u003cli\u003ePower cable (1.8 m)\u003c\/li\u003e\n\u003cli\u003eHexagonal wrench\u003c\/li\u003e\n\u003cli\u003eGloves\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMotor:\u003c\/strong\u003e DC servo\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDrive Method:\u003c\/strong\u003e Belt drive\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpeeds:\u003c\/strong\u003e 33-1\/3 RPM, 45 RPM\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTurntable Platter:\u003c\/strong\u003e 20 mm thick acrylic\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWow and Flutter:\u003c\/strong\u003e \u0026lt;0.12%\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSignal-to-Noise Ratio:\u003c\/strong\u003e \u0026gt;60 dB\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePower Consumption:\u003c\/strong\u003e 6 W\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTonearm\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eType:\u003c\/strong\u003e Static balanced straight carbon tonearm\u003cbr\u003e\u003cstrong\u003eEffective Arm Length:\u003c\/strong\u003e 223.6 mm\u003cbr\u003e\u003cstrong\u003eOverhang:\u003c\/strong\u003e 18.6 mm\u003cbr\u003e\u003cstrong\u003eDownforce Range:\u003c\/strong\u003e 0-3 g\u003cbr\u003e\u003cstrong\u003eCartridge Weight Range (Light, Heavy Counterweight):\u003c\/strong\u003e 6.1-9.2 g, 9.2-13.9 g\u003cbr\u003e\u003cstrong\u003eHeight Adjustment Range:\u003c\/strong\u003e -1.5 mm to +7 mm\u003cbr\u003e\u003cstrong\u003eAntiskate Adjustment Range:\u003c\/strong\u003e 1.3 g-3 g\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReplacement Cartridge:\u003c\/strong\u003e AT-OC9XEN\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReplacement Belt:\u003c\/strong\u003e AT-LPA2\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (WDH):\u003c\/strong\u003e 17\" x 13\" x 5.3\" (420 × 340 × 135 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight\u003cbr\u003eTurntable:\u003c\/strong\u003e 19 lb. (8.4 kg)\u003cbr\u003e\u003cstrong\u003eControl Unit:\u003c\/strong\u003e 2.4 lb. (1.1 kg)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":51103512821944,"sku":"AT-LPA2","price":2000.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at-lpa2_01.webp?v=1749660165"},{"product_id":"audio-technica-at33xen-dual-moving-coil-cartridge","title":"Audio-Technica AT33xEN Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT33xEN Dual Moving-Coil Stereo Cartridge\u003c\/h1\u003e\n\u003ch3\u003eElliptical nude stylus, Duralumin tapered pipe cantilever, composite body with die-cast zinc base for natural balance and warm tone\u003c\/h3\u003e\n\u003cp\u003eThe latest update to the venerable AT33 Series—the first extensive overhaul in years—brings new warmth and fullness to your vinyl playback. Incorporating technological and material improvements, including Audio-Technica’s first use of die-cast zinc at the base of the cartridge to suppress resonance and enhance expressiveness in the mid to low frequencies, the AT33x Series cartridges let you hear the finest details across the audio spectrum.\u003c\/p\u003e\n\u003cp\u003eThe AT33xEN is an excellent all-around cartridge choice, delivering warm, full-bodied audio reproduction. It features a 0.3 × 0.7 mil elliptical nude stylus attached to a hard duralumin tapered pipe cantilever, providing excellent groove tracking with refined high-frequency control. The newly developed suspension mechanism uses piano wire for improved tracking accuracy and slightly lower dynamic compliance, resulting in a more substantial presentation in the mid-low range.\u003c\/p\u003e\n\u003cp\u003eThe cartridge’s composite body, made of die-cast zinc, aluminum, and high-rigidity polymer, reduces and disperses resonance across the entire body for balanced, natural sound reproduction that doesn’t favor particular frequencies. The AT33x dual moving coil design features independent left- and right-channel PCOCC (Pure Copper by Ohno Continuous Casting) coils for outstanding channel separation and smooth, low-distortion signal transmission. A neodymium magnet and permendur yoke generate a powerful magnetic field that maximizes efficiency and resolution, ensuring lifelike analog playback.\u003c\/p\u003e\n\u003cp\u003eLike all AT33x Series cartridges, the AT33xEN includes threaded mounting holes for easy installation using just two screws—especially convenient for integrated tonearms.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePlease Note:\u003c\/strong\u003e The AT33xEN’s stylus assembly is not field-replaceable. Audio-Technica offers a fee-based Moving Coil Exchange Program to properly service your moving coil cartridge.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003cli\u003eWasher × 2\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (M2.6): 8.0 mm × 2, 10.0 mm × 2, 13.0 mm × 2\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eType:\u003c\/b\u003e MC\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFrequency Response:\u003c\/b\u003e 20–40,000 Hz\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eChannel Separation:\u003c\/b\u003e 27 dB \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Angle:\u003c\/b\u003e 19°\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eTracking Force:\u003c\/b\u003e 1.8–2.2 g (2.0 g standard)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eRecommended Load Impedance:\u003c\/b\u003e ≥ 100 ohms (when head amplifier connected)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Impedance:\u003c\/b\u003e 12 ohms \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDC Resistance:\u003c\/b\u003e 12 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Inductance:\u003c\/b\u003e 26 μH \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Voltage:\u003c\/b\u003e 0.4 mV \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Balance:\u003c\/b\u003e 1.0 dB \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Shape:\u003c\/b\u003e Nude Elliptical\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCantilever:\u003c\/b\u003e Duralumin tapered pipe\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStatic Compliance:\u003c\/b\u003e 21 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDynamic Compliance:\u003c\/b\u003e 6 × 10⁻⁶ cm\/dyne (100 Hz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Curvature Radius:\u003c\/b\u003e 0.3 × 0.7 mil\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThreaded Hole:\u003c\/b\u003e M2.6 × 2\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDimensions (HWD):\u003c\/b\u003e 0.63\" × 0.65\" × 1.0\" (16.1 × 16.6 × 26.1 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWeight:\u003c\/b\u003e 10.1 g (0.36 oz)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":51854121140408,"sku":"AT33XEN","price":699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at33xen_02.png?v=1762196911"},{"product_id":"audio-technica-at33xmld-dual-moving-coil-cartridge","title":"Audio-Technica AT33xMLD Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT33xMLD Dual Moving-Coil Stereo Cartridge\u003c\/h1\u003e\n\u003ch3\u003eMicrolinear nude stylus, Duralumin tapered pipe cantilever, composite body with die-cast zinc base for natural balance and warm tone\u003c\/h3\u003e\n\u003cp\u003eThe latest update to the venerable AT33 Series—the first extensive overhaul in years—brings new warmth and fullness to your vinyl playback. Incorporating technological and material improvements, including Audio-Technica’s first use of die-cast zinc at the base of the cartridge to suppress resonance and enhance expressiveness in the mid to low frequencies, the AT33x Series cartridges let you hear the finest details across the audio spectrum.\u003c\/p\u003e\n\u003cp\u003eFeaturing a microlinear nude stylus set to a duralumin tapered pipe cantilever, the AT33xMLD delivers a warm yet detailed sound, making it an excellent choice for rock and jazz records. The newly developed suspension mechanism uses piano wire for improved tracking accuracy and slightly lower dynamic compliance, providing a more substantial presentation in the mid-low range.\u003c\/p\u003e\n\u003cp\u003eThe cartridge’s composite body, made of die-cast zinc, aluminum, and high-rigidity polymer, reduces and disperses resonance across the entire body for balanced, natural sound reproduction that doesn’t favor particular frequencies. The AT33x dual moving coil design features independent left- and right-channel PCOCC (Pure Copper by Ohno Continuous Casting) coils for outstanding channel separation and smooth, low-distortion signal transmission. A neodymium magnet and permendur yoke generate a powerful magnetic field that maximizes efficiency and resolution, ensuring lifelike analog playback.\u003c\/p\u003e\n\u003cp\u003eLike all AT33x Series cartridges, the AT33xMLD includes threaded mounting holes for easy installation using just two screws—especially convenient for integrated tonearms.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePlease Note:\u003c\/strong\u003e The AT33xMLD’s stylus assembly is not field-replaceable. Audio-Technica offers a fee-based Moving Coil Exchange Program to properly service your moving coil cartridge.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003cli\u003eWasher × 2\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (M2.6): 8.0 mm × 2, 10.0 mm × 2, 13.0 mm × 2\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eType:\u003c\/b\u003e MC\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFrequency Response:\u003c\/b\u003e 20–42,000 Hz\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eChannel Separation:\u003c\/b\u003e 27 dB (1 kHz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Angle:\u003c\/b\u003e 19°\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eTracking Force:\u003c\/b\u003e 1.8–2.2 g (2.0 g standard)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eRecommended Load Impedance:\u003c\/b\u003e ≥ 100 ohms (when head amplifier connected)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Impedance:\u003c\/b\u003e 12 ohms (1 kHz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDC Resistance:\u003c\/b\u003e 12 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Inductance:\u003c\/b\u003e 26 μH (1 kHz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Voltage:\u003c\/b\u003e 0.4 mV (1 kHz, 5 cm\/sec.)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Balance:\u003c\/b\u003e 1.0 dB (1 kHz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Shape:\u003c\/b\u003e Nude Microlinear\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCantilever:\u003c\/b\u003e Duralumin tapered pipe\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStatic Compliance:\u003c\/b\u003e 21 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDynamic Compliance:\u003c\/b\u003e 6 × 10⁻⁶ cm\/dyne (100 Hz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Curvature Radius:\u003c\/b\u003e 2.2 × 0.12 mil\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThreaded Hole:\u003c\/b\u003e M2.6 × 2\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDimensions (HWD):\u003c\/b\u003e 0.63\" × 0.65\" × 1.0\" (16.1 × 16.6 × 26.1 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWeight:\u003c\/b\u003e 10.1 g (0.36 oz)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":51854121173176,"sku":"AT33XMLD","price":799.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at33xmld_02.png?v=1762196887"},{"product_id":"audio-technica-at33xmlb-dual-moving-coil-cartridge","title":"Audio-Technica AT33xMLB Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT33xMLB Dual Moving-Coil Stereo Cartridge\u003c\/h1\u003e\n\u003ch3\u003eMicrolinear nude stylus, solid boron tapered cantilever, composite body with die-cast zinc base for enhanced mid-low expressiveness\u003c\/h3\u003e\n\u003cp\u003eThe latest update to the venerable AT33 Series—the first extensive overhaul in years—brings new warmth and fullness to your vinyl playback. Incorporating technological and material improvements, including Audio-Technica’s first use of die-cast zinc at the base of the cartridge to kill resonance and improve expressiveness in the mid to low frequencies.\u003c\/p\u003e\n\u003cp\u003eWith its microlinear nude stylus and solid boron tapered cantilever, the AT33xMLB is capable of capturing the subtlest details cut into a record groove. This capacity for high-resolution tracking is particularly noticeable when listening to orchestral recordings, allowing each instrument to be discerned clearly, or when playing records made since the late 1970s that benefit from high-fidelity recording and manufacturing advancements. The newly developed suspension mechanism uses piano wire for improved tracking accuracy and slightly lower dynamic compliance for more substantial audio, particularly in the mid-low range.\u003c\/p\u003e\n\u003cp\u003eThe cartridge’s composite body, made of die-cast zinc, aluminum, and high-rigidity polymer, reduces and disperses resonance across the entire body, resulting in balanced, natural sound reproduction. The AT33x dual moving coil design features independent left- and right-channel PCOCC (Pure Copper by Ohno Continuous Casting) coils for outstanding channel separation and smooth signal transmission. A neodymium magnet and permendur yoke create a strong magnetic field that maximizes power generation efficiency, ensuring responsive, high-resolution analog playback. Like all AT33x Series cartridges, the body includes threaded holes for easy mounting (just two screws required), which is especially helpful with integrated tonearms.\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003ePlease Note:\u003c\/i\u003e AT33xMLB’s stylus assembly is not field-replaceable. Audio-Technica offers a fee-based Moving Coil Exchange Program to properly service your moving coil cartridge.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003cli\u003eWasher × 2\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (M2.6): 8.0 mm × 2, 10.0 mm × 2, 13.0 mm × 2\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eType:\u003c\/b\u003e MC\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFrequency Response:\u003c\/b\u003e 20–45,000 Hz\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eChannel Separation:\u003c\/b\u003e 27 dB \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Angle:\u003c\/b\u003e 19°\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eTracking Force:\u003c\/b\u003e 1.8–2.2 g (2.0 g standard)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eRecommended Load Impedance:\u003c\/b\u003e ≥ 100 ohms (when head amplifier connected)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Impedance:\u003c\/b\u003e 12 ohms \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDC Resistance:\u003c\/b\u003e 12 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Inductance:\u003c\/b\u003e 26 μH \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Voltage:\u003c\/b\u003e 0.42 mV \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Balance:\u003c\/b\u003e 1.0 dB (1 kHz)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Shape:\u003c\/b\u003e Nude Microlinear\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCantilever:\u003c\/b\u003e Nude tapered boron\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStatic Compliance:\u003c\/b\u003e 19 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDynamic Compliance:\u003c\/b\u003e 6 × 10⁻⁶ cm\/dyne \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Curvature Radius:\u003c\/b\u003e 2.2 × 0.12 mil\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eArmature Structure:\u003c\/b\u003e Double-step design for increased rigidity\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eTerminal Pins:\u003c\/b\u003e Thick gold-plated, low-resistance\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThreaded Hole:\u003c\/b\u003e M2.6 × 2\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDimensions (WHD):\u003c\/b\u003e 0.65\" x 0.63\" x 1.0\" (16.6 x 16.0 x 26.1 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWeight:\u003c\/b\u003e 10.1 g\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":51854121205944,"sku":"AT33XMLB","price":899.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at33xmlb_02.png?v=1762196858"},{"product_id":"audio-technica-at33xmono-i-dual-moving-coil-cartridge","title":"Audio-Technica AT33xMONO\/I Dual Moving Coil Mono Cartridge","description":"\u003ch1\u003eAudio-Technica AT33xMONO\/I Moving-Coil Mono Cartridge\u003c\/h1\u003e\n\u003ch3\u003eDual moving coil with horizontal PCOCC coils, 0.65 mil conical stylus with duralumin cantilever, safe on stereo records\u003c\/h3\u003e\n\u003cp\u003eThe AT33xMONO\/I is a purpose-built mono cartridge engineered for microgroove vinyl (i.e. not shellac records).\u003c\/p\u003e\n\u003cp\u003eIts rigid body uses Hanenite, Audio-Technica's proprietary high-damping material. The voice coils are arranged horizontally so the generator responds only to horizontal groove motion—the information that encodes mono. Compliance is still appropriate in the vertical plane, making it safe to use on stereo records.\u003c\/p\u003e\n\u003cp\u003eA 0.65 mil conical stylus is mounted to a hard duralumin cantilever for dependable tracking and stable tone. The PCOCC (Pure Copper by Ohno Continuous Casting) coils provide a clean signal path, and the design’s rejection of vertical artifacts helps the cartridge ignore many of the strain components that come from groove wear and light damage, yielding cleaner mono playback than a typical stereo cartridge summed to mono.\u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 washers\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (M2.6, 8 mm × 2, 10 mm × 2, 13 mm × 2)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eType:\u003c\/b\u003e Moving coil (dual), mono\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFrequency Response:\u003c\/b\u003e 20 Hz–30 kHz\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Voltage (1 kHz, 5 cm\/s):\u003c\/b\u003e 0.42 mV\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Channel Balance (1 kHz):\u003c\/b\u003e 1 dB\u003cbr\u003e\u003cbr\u003e\u003cb\u003eHorizontal\/Vertical Output Ratio:\u003c\/b\u003e 25 dB\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Angle:\u003c\/b\u003e 20°\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Force:\u003c\/b\u003e 2.0 g–2.4 g (2.2 g standard)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eRecommended Load Impedance:\u003c\/b\u003e More than 100 ohms (with head amplifier)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Impedance (1 kHz):\u003c\/b\u003e 10 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDC Resistance:\u003c\/b\u003e 10 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Inductance (1 kHz):\u003c\/b\u003e 27 µH\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Shape:\u003c\/b\u003e 0.65 mil conical\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCantilever:\u003c\/b\u003e Duralumin pipe\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStatic Compliance:\u003c\/b\u003e 14 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDynamic Compliance (100 Hz):\u003c\/b\u003e 6 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eMounting:\u003c\/b\u003e Half-inch\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDimensions (WHD):\u003c\/b\u003e 0.65\" × 0.63\" × 1.03\" (16.6 × 16.1 × 26.1 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWeight:\u003c\/b\u003e 10.1 g\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":51854121271480,"sku":"AT33XM1","price":649.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at33xmono_1_02.png?v=1762196747"},{"product_id":"audio-technica-at33xmono-ii-dual-moving-coil-cartridge","title":"Audio-Technica AT33xMONO\/II Dual Moving Coil Mono Cartridge","description":"\u003ch1\u003eAudio-Technica AT33xMONO\/II Moving Coil Mono Cartridge\u003c\/h1\u003e\n\u003ch3\u003eDual moving coil with horizontal PCOCC coils, 0.65 mil conical stylus with duralumin cantilever, safe on stereo records\u003c\/h3\u003e\n\u003cp\u003eThe AT33xMONO\/II is a purpose-built mono cartridge engineered for microgroove vinyl (i.e. not shellac records).\u003c\/p\u003e\n\u003cp\u003eIts rigid body uses Hanenite, Audio-Technica's proprietary high-damping material. The voice coils are arranged horizontally so the generator responds only to horizontal groove motion—the information that encodes mono. Compliance is still appropriate in the vertical plane, making it safe to use on stereo records.\u003c\/p\u003e\n\u003cp\u003eA 0.65 mil conical stylus is mounted to a hard duralumin cantilever for dependable tracking and stable tone. The PCOCC (Pure Copper by Ohno Continuous Casting) coils provide a clean signal path, and the design’s rejection of vertical artifacts helps the cartridge ignore many of the strain components that come from groove wear and light damage, yielding cleaner mono playback than a typical stereo cartridge summed to mono. \u003c\/p\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003e2 washers\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (M2.6, 8 mm × 2, 10 mm × 2, 13 mm × 2)\u003c\/li\u003e\n\u003cli\u003ePlastic protector\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eType:\u003c\/b\u003e Moving coil (dual), mono\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFrequency Response:\u003c\/b\u003e 20 Hz–20 kHz\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Voltage (1 kHz, 5 cm\/s):\u003c\/b\u003e 0.37 mV\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Channel Balance (1 kHz):\u003c\/b\u003e 1 dB\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eHorizontal\/Vertical Output Ratio:\u003c\/strong\u003e 25 dB\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Angle:\u003c\/b\u003e 20°\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Force:\u003c\/b\u003e 2.3 g–2.7 g (2.5 g standard)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eRecommended Load Impedance:\u003c\/b\u003e More than 100 ohms (with head amplifier)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Impedance (1 kHz):\u003c\/b\u003e 10 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDC Resistance:\u003c\/b\u003e 10 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Inductance (1 kHz):\u003c\/b\u003e 27 µH\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Shape:\u003c\/b\u003e 0.65 mil conical\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCantilever:\u003c\/b\u003e Duralumin pipe\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStatic Compliance:\u003c\/b\u003e 14 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDynamic Compliance (100 Hz):\u003c\/b\u003e 6 × 10⁻⁶ cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eMounting:\u003c\/b\u003e Half-inch\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eBody Material:\u003c\/b\u003e Aluminium\/Synthetic Resin\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDimensions (WHD):\u003c\/b\u003e 0.65\" × 0.63\" × 1.04\" (16.6 × 16.0 × 26.5 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWeight:\u003c\/b\u003e 10.1 g \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":51854121304248,"sku":"AT33XM2","price":449.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at33xmono_2_02.png?v=1762196817"},{"product_id":"audio-technica-cork-record-mat","title":"Audio-Technica AT-SMC1 Cork Record Mat","description":"\u003ch1\u003eAudio-Technica AT-SMC1 Cork Record Mat\u003c\/h1\u003e\n\u003cp\u003eThe AT-SMC1 cork slipmat enhances the sound quality of your records by reducing vibrations and unwanted resonance, ensuring clearer audio playback.\u003c\/p\u003e\n\u003cp\u003eAt 1.6 mm, the slipmat offers a good balance between flexibility and support, providing a stable platform for records that minimizes slippage during playback. This 295 mm (11.6\") diameter slipmat fits most standard turntables and won’t attract dust or shed particles like some other cork or felt mats. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eReduces vibration and resonance\u003c\/li\u003e\n\u003cli\u003eProvides a stable platform for records \u003c\/li\u003e\n\u003cli\u003eDoesn't attract dust or shed particles\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (Thickness, Diameter):\u003c\/strong\u003e  1.6 mm, 295 mm (11.6\")\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 30 g\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":52177771004088,"sku":"AT-SMC1","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/Background_cdfca3f9-0ed1-4f10-b478-30713d8a2a9c.jpg?v=1761845523"},{"product_id":"audio-technica-cork-rubber-record-mat","title":"Audio-Technica AT-SMCR2 Cork \u0026 Rubber Record Mat","description":"\u003ch1\u003eAudio-Technica AT-SMCR2 Cork \u0026amp; Rubber Record Mat\u003c\/h1\u003e\n\u003cp\u003eMade from a blend of cork and rubber, the AT-SMCR2 slipmat absorbs a wider range of vibrations, especially lower frequencies, than standard cork slipmats, helping to deliver clearer audio playback from your records.\u003c\/p\u003e\n\u003cp\u003eThe rubber also adds mass to the mat, creating a stable platform that improves tracking and prevents minor skips or jumps. Plus, the cork-rubber blend has excellent antistatic properties, so you’ll hear fewer of those annoying pops and clicks that result from static discharge.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAbsorbs a wider range of vibrations, especially lower frequencies\u003c\/li\u003e\n\u003cli\u003eRubber adds mass \u003c\/li\u003e\n\u003cli\u003eReduces static buildup\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eDimensions (Thickness, Diameter):\u003c\/strong\u003e  2 mm, 295 mm (11.6\")\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 96 g\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":52177771036856,"sku":"AT-SMCR2","price":35.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/Background.jpg?v=1761845378"},{"product_id":"audio-technica-azimuth-vta-alignment-tool","title":"Audio-Technica AT-VTAZ1 Azimuth + VTA Alignment Tool","description":"\u003ch1\u003eAudio-Technica AT-VTAZ1 Azimuth + VTA Alignment Tool\u003c\/h1\u003e\n\u003ch3\u003eDual-purpose tool allows you to set azimuth and VTA (vertical tracking angle) for precise tracking and proper playback geometry\u003c\/h3\u003e\n\u003cp\u003eUse this tool to achieve accurate tonearm height and cartridge azimuth alignment for precise tracking and proper playback geometry.\u003c\/p\u003e\n\u003ch4\u003eAbout the VTA Alignment\u003cbr\u003e\n\u003c\/h4\u003e\n\u003cp\u003eVTA (vertical tracking angle) refers to the angle formed by the record surface and the line from the stylus (in the groove) to the cantilever pivot point. Incorrect VTA can lead to uneven stylus wear and potential damage to your records over time.\u003c\/p\u003e\n\u003cp\u003eThe thickness of a record can also alter the VTA slightly. Thicker records (e.g., 180-gram vinyl) may require slightly different tonearm settings than thinner records. This also applies to phono cartridges, which may vary significantly in height. Some tonearms are equipped with a dedicated VTA or tonearm height adjustment dial that makes changes quick and easy. This is helpful if you frequently switch between records of different thicknesses or cartridges of different sizes.\u003c\/p\u003e\n\u003ch4\u003eAbout the Azimuth Alignment\u003cbr\u003e\n\u003c\/h4\u003e\n\u003cp\u003eAzimuth refers to the angle of the stylus when viewed from the front, specifically whether the stylus is exactly vertical and symmetrical as it sits in the record groove. Proper azimuth alignment ensures that the stylus is equidistant from both walls of the record groove, which is important for proper stereo imaging, equal channel balance, and minimal distortion. Misaligned azimuth can cause uneven wear on your records and stylus, potentially damaging both over time.\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":52177771069624,"sku":"AT-VTAZ1","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at-vtaz1_01_1.png?v=1761845149"},{"product_id":"audio-technica-multi-function-cartridge-alignment-strobe-disc","title":"Audio-Technica Stroboscope Disc w\/ Overhand Gauge","description":"\u003ch1\u003eAudio-Technica Stroboscope Disc w\/ Overhand Gauge\u003c\/h1\u003e\n\u003cp\u003eThe AT6180a stroboscope enables you to check the rotation speed of your turntable. It features high-contrast markings for 33-1\/3 and 45 RPM at both 50 and 60 Hz. It also includes a 10–20 mm overhang gauge.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eStroboscope confirms turntable rotation speed (33-1\/3 \u0026amp; 45 RPM at 50\/60 Hz)\u003c\/li\u003e\n\u003cli\u003eHigh-contrast black markings on silver scope\u003c\/li\u003e\n\u003cli\u003eIncludes 10–20 mm overhang gauge\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":52177771135160,"sku":"AT-CAP4","price":32.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/AUD-AT6180A_jpg.webp?v=1761844935"},{"product_id":"audio-technica-cartridge-alignment-protractor","title":"Audio-Technica AT-CAP1 Cartridge Alignment Protractor","description":"\u003ch1\u003eAudio-Technica AT-CAP1 Cartridge Alignment Protractor\u003c\/h1\u003e\n\u003cp\u003eThis protractor uses the Baerwald alignment method to set a phono cartridge’s offset angle and null points. Cartridge alignment is critical for optimal playback, ensuring that the stylus tip remains as tangent to the record groove as possible as it travels across the record. \u003c\/p\u003e\n\u003cp\u003eTypically, if your tonearm’s effective length (the distance from the tonearm pivot to the stylus tip) falls between 222 mm (8.7\") and 250 mm (9.8\"), you can use the Baerwald method to align the cartridge.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":52177771167928,"sku":"AT-CAP1","price":17.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/ATCAP1.jpg?v=1761844799"},{"product_id":"audio-technica-premium-disk-stabilizer","title":"Audio-Technica AT628a Stainless Steel Disk Stabilizer","description":"\u003ch1\u003eAudio-Technica AT628a Stainless Steel Disk Stabilizer\u003c\/h1\u003e\n\u003ch3\u003eA 450 g weight with two recessed inner rings\u003c\/h3\u003e\n\u003cp\u003eMinimize record resonance and vibration with this heavy damper that sits over the turntable spindle and holds the record firmly in place. The precision-machined stainless-steel AT628a pairs \u003cspan style=\"font-size: 0.875rem;\"\u003ewell with modern turntable designs and resists\u003c\/span\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e corrosion and tarnish. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eIt is m\u003c\/span\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eachined for easy gripping, and it features two recessed inner rings on its underside to accommodate records that are slightly warped or that bulge near the spindle hole. And since it’s not magnetic, the stabilizer poses no interference risk with phono cartridges.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eThe AT628a weighs 450 g and fits spindles up to 21 mm in length. Check with your turntable’s manufacturer to confirm that it can support the weight of the AT628a.\u003c\/p\u003e\n\u003cp\u003eThe AT628a should not be used with the following Audio-Technica turntables: AT- AT-LP3XBT, AT-LPW30, and all entry-level models, including the Sound Burger and turntables in the AT-LP60, AT-LP60X and AT-LP70X Series. \u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePrecision-machined stainless-steel stabilizer holds records firmly in place for reduced resonance and improved sound quality\u003c\/li\u003e\n\u003cli\u003eTwo recessed inner rings on the underside of the stabilizer accommodate records that bulge slightly near the spindle hole \u003c\/li\u003e\n\u003cli\u003eEasy to grip with fingers\u003c\/li\u003e\n\u003cli\u003eApprox. 450 g (15.9 oz)\u003c\/li\u003e\n\u003cli\u003eFits spindles up to 21 mm long\u003c\/li\u003e\n\u003cli\u003eWorks with a wide variety of turntables, including most Audio-Technica step-up and premium models. (Always check with the manufacturer first.)\u003c\/li\u003e\n\u003cli\u003eMade in Japan\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eFit:\u003c\/strong\u003e Spindles up to 21 mm\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 450 g (15.9 oz)\u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":52177771200696,"sku":"AT628A","price":79.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/aud_at628a_jpg.webp?v=1761844689"},{"product_id":"audio-technica-at-mcd1-dual-moving-coil-cartridge","title":"Audio-Technica AT-MCD1 Dual Moving Coil Cartridge","description":"\u003ch1\u003eAudio-Technica AT-MCD1 Dual Moving Coil Stereo Cartridge\u003c\/h1\u003e\n\u003ch3\u003eFlagship iron-core moving coil cartridge with a unified Shibata stylus and 0.22 mm square diamond cantilever\u003c\/h3\u003e\n\u003cp\u003eThe Audio-Technica AT-MCD1 is the company’s flagship iron-core moving coil cartridge, designed to build on the limited-edition AT-MC2022 60th anniversary model. It carries forward that cartridge’s one-piece diamond stylus-cantilever construction while further reducing cantilever mass and using a newly developed Shibata stylus for finer groove tracing.\u003c\/p\u003e\n\u003cp\u003eThe AT-MCD1’s unified Shibata stylus and 0.22 mm square diamond cantilever are formed from a single lab-grown diamond. By eliminating the conventional bond between stylus and cantilever, this structure allows groove vibrations to pass more directly to the coils, supporting fast transient response, high-frequency extension, low noise, and a more complete retrieval of fine detail.\u003c\/p\u003e\n\u003cp\u003eIts dual moving coil generator uses independent PCOCC coils and a dedicated magnetic circuit developed for Audio-Technica’s high-class moving coil cartridges. A hybrid body with a titanium housing, aluminum base, and elastomer undercover helps disperse unwanted resonance, while threaded mounting holes, 3 micron gold-plated terminal pins, and hand-finished Japanese construction round out the design.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eUnified diamond stylus-cantilever\u003c\/li\u003e\n\u003cli\u003eNewly developed Shibata stylus\u003c\/li\u003e\n\u003cli\u003e0.22 mm square diamond cantilever\u003c\/li\u003e\n\u003cli\u003eDual moving coil construction\u003c\/li\u003e\n\u003cli\u003ePCOCC moving coils\u003c\/li\u003e\n\u003cli\u003eTitanium, aluminum, and elastomer body\u003c\/li\u003e\n\u003cli\u003eThreaded mounting holes\u003c\/li\u003e\n\u003cli\u003eGold-plated terminal pins\u003c\/li\u003e\n\u003cli\u003eUnique engraved serial number\u003c\/li\u003e\n\u003cli\u003eHand-finished in Japan\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIncluded Accessories\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-magnetic screwdriver\u003c\/li\u003e\n\u003cli\u003eBrush\u003c\/li\u003e\n\u003cli\u003eWashers x 2\u003c\/li\u003e\n\u003cli\u003eCartridge installation screws (M2.6): 5 mm (0.20\") x 2, 8 mm (0.31\") x 2, 10 mm (0.39\") x 2, 12 mm (0.47\") x 2\u003c\/li\u003e\n\u003cli\u003eProtector\u003c\/li\u003e\n\u003cli\u003eWooden case\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eType:\u003c\/b\u003e MC\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eFrequency Response:\u003c\/b\u003e 20 Hz–50 kHz\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eChannel Separation (1 kHz):\u003c\/b\u003e 28 dB\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eVertical Tracking Angle:\u003c\/b\u003e 20°\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eTracking Force (1.8 g standard):\u003c\/b\u003e 1.7 g–1.9 g\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eRecommended Load Impedance (When Head Amplifier Connected):\u003c\/b\u003e 100 ohms or greater\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Impedance (1 kHz):\u003c\/b\u003e 12 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDC Resistance:\u003c\/b\u003e 12 ohms\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCoil Inductance (1 kHz):\u003c\/b\u003e 25 μH\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Voltage (1 kHz, 5 cm\/sec.):\u003c\/b\u003e 0.55 mV\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eOutput Balance (1 kHz):\u003c\/b\u003e 0.5 dB\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Shape (Integrated Cantilever Type):\u003c\/b\u003e Shibata\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStylus Curvature Radius:\u003c\/b\u003e 2.7 x 0.08 mil\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eCantilever:\u003c\/b\u003e 0.22 mm square diamond\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eStatic Compliance:\u003c\/b\u003e 21 x 10\u003csup\u003e-6\u003c\/sup\u003e cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDynamic Compliance (100 Hz):\u003c\/b\u003e 15 x 10\u003csup\u003e-6\u003c\/sup\u003e cm\/dyne\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eThreaded Hole:\u003c\/b\u003e M2.6 x 2\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eDimensions (WHD):\u003c\/b\u003e 17.7 mm x 17.3 mm x 26.7 mm \u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eWeight:\u003c\/b\u003e 9.5 g \u003c\/p\u003e","brand":"Audio Technica","offers":[{"title":"Default Title","offer_id":53545113878712,"sku":"AT-MCD1","price":11000.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1564\/1247\/files\/at-mcd1_02_png.webp?v=1780583190"}],"url":"https:\/\/upscaleaudio.pro\/collections\/audio-technica.oembed","provider":"Upscale Audio","version":"1.0","type":"link"}